摘要:
An apparatus for a central augering system within a cleaning system. This central auger system provides several advantages including: 1) reduction in size of the overall cleaner; 2) prevention of bridging in the cleaner housing due to the close proximity of the auger to the detoning roll the toner falls directly into the auger; and 3) the second detoning roll which sees only a small amount of toner is lubricated by the toner in the auger.
摘要:
An apparatus in which a six bar linkage cleaner brush retraction/engagement mechanism enables brush retraction (and engagement with the photoreceptor) while providing good control over the brush interference and the capability of changing all of the timing parameters through clutch actuation times in software and clutch shaft speed. The mechanism allows the brushes to retract and engage the photoreceptor independently of one another with relatively soft contacts to the photoreceptor to minimize impacts to photoreceptor motion quality. A four position clutch is used to provide magnetic pole sensor outputs to the system controller to decide when the clutch, which drives the six bar linkage, is engaged and disengaged. The index wheel of the clutch has four equally spaced magnets that are located relative to the retraction crank shaft so that there is a significant amount of time between detecting a pole and the corresponding desired state. An encoder is used to monitor the mechanical drift of each cleaner state.
摘要:
An apparatus and method for retracting the cleaner from an imaging surface and preventing toner leakage. An apparatus and method that describes a DESB (i.e. dual electrostatic brush) cleaner in a multi-pass operation that not only has to clean the toner from the photoreceptor, but has to retract from the photoreceptor. The two brushes pivot about two defined pivot points in the cleaner housing during the retraction cycle to disengage from the photoreceptor during multi-pass operations. The first brush is pivoted up and the second brush is pivoted down. A further disclosure is the apparatus and method of using thin sliding and flexible plastic seals for a dual ESB that has moving (e.g. camming in and out) housings. The seals prevent leakage of the toner particles from the cleaner housing.
摘要:
An apparatus and method is disclosed for increasing brush life and reducing emissions by removing accumulated toner using detoning cycles. A further embodiment of the disclosure is a method for periodic brush-reversing detoning cycle occurring during a standby condition.
摘要:
An apparatus and method for moving a cleaning brush, periodically or continuously, to avoid flat spots or voids in the cleaning brush fibers when the printing machine is in standby or off. Periodic movement of the cleaning brush or slow rotation of the cleaning brush when the machine is in a non-operational mode prevent brush "set" from occurring thus, preventing motion quality errors in the printing operation.
摘要:
An apparatus and printing machine that contain a cleaner brush with long sweeper fibers orientated along the overall width of the brush, and having a greater length than the majority of fibers of the brush to remove the particles that adhere to the cleaner housing and thus, prevent toner droppings.
摘要:
A method to evaluate the cleaning performance of brush cleaners by measuring the brush to photoreceptor nip width (e.g cleaning footprint or contact zone) using an ESV sensor or ETAC sensor. This nip width measurement is automatically made using one of the sensing devices. The nip width measurement is converted into diagnostic information using a software algorithm or similar mode of conversion. The diagnostic information can be used in a variety of ways such as a diagnostic tool for a technical representative to warn against the end of brush life, to adjust cleaner biases for automatic changes in setup to achieve better cleaning, to predict brush replacement, to correct brush BPI (i.e. brush to photoreceptor interference) for an under or over engaged brush.
摘要:
A method and an apparatus for identifying cleaner retraction timing faults in an electrostatographic printer. A toner image or patch is developed on the photoreceptor during the non-printing mode of the printer. After cleaning by a retractable cleaner, the portion of the image or patch not cleaned is measured and compared to a predetermined length in order to determine cleaner retracting timing faults in the cleaner subsystem.
摘要:
An apparatus and method that uses a toner valve to seal the interface between a cleaner housing and waste container. The toner valve incorporates a two piece valve of which the larger, called the main valve, is housed in the cleaner housing, and the smaller, called the lid, is housed in the top of the waste container. When the waste container is inserted onto the cleaner housing, the main valve of the cleaner housing is coupled to the lid of the waste container. A handle extending from a shaft in the main valve enables movement of the complete toner valve. The coupling of the two piece toner valve enables the toner valve to work as a single unit when the handle is rotated, opening the waste container and the cleaner housing and providing a totally sealed open path for the toner to fall from the cleaner housing to the waste container. Further rotation of the two piece toner valve closes both the cleaner housing and the waste container. The main valve seals the cleaner housing preventing toner from escaping and the lid seals the waste container preventing toner from spilling upon removal from the cleaner housing.
摘要:
A cleaning method and apparatus that provides lubrication to a secondary detoning roll in a cleaner brush system, thus reducing cleaning failures. The toner particles removed from the first detoning roll are transported to the second detoning roll. This allows lubrication of the second detoning roll and reduces the wear problem of the second detoning roll due to lack of lubrication.