摘要:
Although the duplexer in a full-duplex transceiver circuit may only be guaranteed by the duplexer manufacturer to have a transmit band rejection from its TX port to its RX port of a certain amount, and may only be guaranteed to have a receive band rejection of another amount, the actual transmit band rejection and the actual receive band rejection of a particular instance of the duplexer may be better than specified. Rather than consuming excess power in the receiver and/or transmitter in order to meet performance requirements assuming the duplexer only performs as well as specified, the duplexer's in-circuit performance is measured as part of a transmitter-to-receiver isolation determination. Transmitter and/or receiver power settings are reduced where possible to take advantage of the measured better-than-specified in-circuit duplexer performance, while still meeting transceiver performance requirements. Power settings are not changed during normal transmit and receive mode operation.
摘要:
Although the duplexer in a full-duplex transceiver circuit may only be guaranteed by the duplexer manufacturer to have a transmit band rejection from its TX port to its RX port of a certain amount, and may only be guaranteed to have a receive band rejection of another amount, the actual transmit band rejection and the actual receive band rejection of a particular instance of the duplexer may be better than specified. Rather than consuming excess power in the receiver and/or transmitter in order to meet performance requirements assuming the duplexer only performs as well as specified, the duplexer's in-circuit performance is measured as part of a transmitter-to-receiver isolation determination. Transmitter and/or receiver power settings are reduced where possible to take advantage of the measured better-than-specified in-circuit duplexer performance, while still meeting transceiver performance requirements. Power settings are not changed during normal transmit and receive mode operation.
摘要:
Although the duplexer in a full-duplex transceiver circuit may only be guaranteed by the duplexer manufacturer to have a transmit band rejection from its TX port to its RX port of a certain amount, and may only be guaranteed to have a receive band rejection of another amount, the actual transmit band rejection and the actual receive band rejection of a particular instance of the duplexer may be better than specified. Rather than consuming excess power in the receiver and/or transmitter in order to meet performance requirements assuming the duplexer only performs as well as specified, the duplexer's in-circuit performance is measured as part of a transmitter-to-receiver isolation determination. Transmitter and/or receiver power settings are reduced where possible to take advantage of the measured better-than-specified in-circuit duplexer performance, while still meeting transceiver performance requirements. Power settings are not changed during normal transmit and receive mode operation.
摘要:
Although the duplexer in a full-duplex transceiver circuit may only be guaranteed by the duplexer manufacturer to have a transmit band rejection from its TX port to its RX port of a certain amount, and may only be guaranteed to have a receive band rejection of another amount, the actual transmit band rejection and the actual receive band rejection of a particular instance of the duplexer may be better than specified. Rather than consuming excess power in the receiver and/or transmitter in order to meet performance requirements assuming the duplexer only performs as well as specified, the duplexer's in-circuit performance is measured as part of a transmitter-to-receiver isolation determination. Transmitter and/or receiver power settings are reduced where possible to take advantage of the measured better-than-specified in-circuit duplexer performance, while still meeting transceiver performance requirements. Power settings are not changed during normal transmit and receive mode operation.
摘要:
Techniques for controlling operation of control loops in a receiver are described. The operation of at least one control loop is modified in conjunction with a change in operating state, which may correspond to a change in linearity state, gain state, operating frequency, antenna configuration, etc. A change in linearity state may occur when jammers are detected and may cause bias current of analog circuit blocks to be adjusted. The at least one control loop to be modified may include a DC loop, an AGC loop, etc. The operation of a control loop may be modified by disabling the control loop or changing its time constant prior to changing operating state, waiting a predetermined amount of time to allow the receiver to settle, and enabling the control loop or restoring its time constant after waiting the predetermined amount of time.
摘要:
Techniques for operating a receiver to linearity performance and higher receive signal to noise ratio are described. The receiver includes one or more circuit blocks, e.g., a low noise amplifier (LNA), having discrete gain states. The gain states are selected based on switch points, with each switch point indicating a specific received signal level at which to switch from one gain state to another gain state. The switch points may be dynamically selected based on channel conditions, which may be characterized by the presence or absence or strength or frequency of jammers. A first set of switch points may be selected when jammers are detected, and a second set of switch points may be selected when jammers are not detected. The gain states are selected in accordance with the set of switch points selected for use.
摘要:
A method for interference reduction is described. The method is implemented in a wireless device. It is determined that a page is going to be received via a secondary receiver. It is also determined that a digital-to-analog converter (DAC) image from a transmitter will cause interference with the secondary receiver when the page is received. A sampling frequency of the DAC for the transmitter is changed so that there are not any DAC images from the transmitter that will cause interference with the secondary receiver.
摘要:
Techniques for controlling operation of control loops in a receiver are described. The operation of at least one control loop is modified in conjunction with a change in operating state, which may correspond to a change in linearity state, gain state, operating frequency, antenna configuration, etc. A change in linearity state may occur when jammers are detected and may cause bias current of analog circuit blocks to be adjusted. The at least one control loop to be modified may include a DC loop, an AGC loop, etc. The operation of a control loop may be modified by disabling the control loop or changing its time constant prior to changing operating state, waiting a predetermined amount of time to allow the receiver to settle, and enabling the control loop or restoring its time constant after waiting the predetermined amount of time.
摘要:
A method and apparatus for avoiding receiver interference is described herein. One or more potential interferers are determined and the frequency associated with the interferers is also determined A desired sampling frequency for the receiver is calculated to avoid the potential interferers.
摘要:
Circuitry configured for dynamically adjusting clock signal quality based on an operating mode for power savings is described. The circuitry includes clock generation circuitry. The circuitry also includes mode control circuitry. The mode control circuitry provides a drive signal based on an operating mode. The circuitry also includes clock buffer circuitry coupled to the clock generation circuitry and to the mode control circuitry. The clock buffer circuitry adjusts a clock signal quality based on the drive signal.