-
公开(公告)号：US4292766A
公开(公告)日：1981-10-06
申请号：US108364
申请日：1979-12-31
CPC分类号： B24B47/206 , B24B5/04 , B24B5/42 , Y10T409/303864 , Y10T409/307336 , Y10T409/30756
摘要： An improved grinding method and apparatus is advantageously used to sequentially grind the pins of a crankshaft. During the grinding of each crankpin, the pin is supported by a steadyrest. During an initial grinding operation, the crankpins are measured or gauged to determine if they are out-of-round by an amount which is greater than the tolerances for the finished crankshaft and less than a maximum amount. If a crankpin is out-of-round by an amount which is equal to or greater than a maximum amount, the crankshaft is rejected. However, if a crankpin is out-of-round by an amount which is less than the maximum amount and more than the tolerance for a finished pin, a second grinding operation is initiated after the initial grinding operation has been completed. During the initial and second grinding operations, a main drive motor is effective to press the steadyrest against the crankpins. A secondary drive motor is provided to adjust the position of the steadyrest to compensate for the smaller size to which the crankpins are ground during the second grinding operation. The finished crankshaft is removed from the grinding machine only after both the initial and second grinding operations have been completed. When the number of consecutive out-of-round crankpins and/or crankshafts becomes excessive, a control signal initiates shutting down of the grinding machine and the establishing of an alarm to prevent the grinding of a large number of out-of-round crankshafts.
摘要翻译： 改进的研磨方法和设备有利地用于顺序研磨曲轴的销。 在每个曲柄销的磨削期间，销由一个稳定支架支撑。 在初始研磨操作期间，测量或测量曲柄销以确定它们是否不圆度大于成品曲轴的公差并小于最大量。 如果曲轴销不合适的量大于或等于最大值，则曲轴被排除。 然而，如果曲轴销不合适的量小于最大量并且大于成品销的公差，则在初始研磨操作完成之后开始第二研磨操作。 在初始和第二次研磨操作期间，主驱动马达有效地将稳定器压靠在曲柄销上。 提供二次驱动电机以调节稳定器的位置，以补偿在第二次磨削操作期间曲柄销被磨削的较小尺寸。 仅在初次和第二次研磨操作完成后，才将完成的曲轴从研磨机中取出。 当连续不完整的曲柄销和/或曲轴的数量变得过大时，控制信号开始关闭磨床并建立报警器，以防止磨削大量的外圆曲轴。
-
公开(公告)号：US4201016A
公开(公告)日：1980-05-06
申请号：US886996
申请日：1978-03-16
CPC分类号： B24B47/206 , B24B5/04 , B24B5/42
摘要： An improved grinding method and apparatus is advantageously used to sequentially grind the pins of a crankshaft. During the grinding of each crankpin, the pin is supported by a steadyrest. During an initial grinding operation, the crankpins are measured or gauged to determine if they are out-of-round by an amount which is greater than the tolerances for the finished crankshaft and less than a maximum amount. If a crankpin is out-of-round by an amount which is equal to or greater than a maximum amount, the crankshaft is rejected. However, if a crankpin is out-of-round by an amount which is less than the maximum amount and more than the tolerances for a finished pin, a second grinding operation is initiated after the initial grinding operation has been completed. During the initial and second grinding operations, a main drive motor is effective to press the steadyrest against the crankpins. A secondary drive motor is provided to adjust the position of the steadyrest to compensate for the smaller size to which the crankpins are ground during the second grinding operation. The finished crankshaft is removed from the grinding machine only after both the initial and second grinding operations have been completed. When the number of consecutive out-of-round crankpins and/or crankshafts becomes excessive, a control signal initiates shutting down of the grinding machine and the establishing of an alarm to prevent the grinding of a large number of out-of-round crankshafts.
摘要翻译： 改进的研磨方法和设备有利地用于顺序研磨曲轴的销。 在每个曲柄销的磨削期间，销由一个稳定支架支撑。 在初始研磨操作期间，测量或测量曲柄销以确定它们是否不圆度大于成品曲轴的公差并小于最大量。 如果曲轴销不合适的量大于或等于最大值，则曲轴被排除。 然而，如果曲柄销不合适的量小于最大量并且大于成品销的公差，则在初始研磨操作完成之后开始第二研磨操作。 在初始和第二次研磨操作期间，主驱动马达有效地将稳定器压靠在曲柄销上。 提供二次驱动电机以调节稳定器的位置，以补偿在第二次磨削操作期间曲柄销被磨削的较小尺寸。 仅在初次和第二次研磨操作完成后，才将完成的曲轴从研磨机中取出。 当连续不完整的曲柄销和/或曲轴的数量变得过大时，控制信号开始关闭磨床并建立报警器，以防止磨削大量的外圆曲轴。
-
搜索结果
2 条记录 (耗时 0.021 秒)
