Process for treating aluminum electrolytic capacitor foil
    2.
    发明授权
    Process for treating aluminum electrolytic capacitor foil 失效
    铝电解电容器箔的处理方法

    公开(公告)号:US4470885A

    公开(公告)日:1984-09-11

    申请号:US464226

    申请日:1983-02-07

    CPC分类号: H01G9/04 C23C22/74 C25D11/16

    摘要: Aluminum electrolytic capacitor foil is treated after etching but before anodizing by first contacting it with a phosphate solution and then heat treating for 30 to 90 seconds to form a thermal oxide layer of controlled thickness. On subsequent anodization, the thermal oxide layer modifies the barrier oxide layer increasing its dielectric strength and hence capacitance and also stabilizes the barrier oxide layer.

    摘要翻译: 铝电解电容器箔经蚀刻处理,但在阳极氧化之前,首先将其与磷酸盐溶液接触,然后热处理30至90秒以形成受控厚度的热氧化物层。 在随后的阳极氧化中,热氧化物层改变阻挡氧化物层增加其介电强度并因此增加电容,并且还使阻挡氧化物层稳定。

    Anodization of aluminum capacitor electrode foil
    3.
    发明授权
    Anodization of aluminum capacitor electrode foil 失效
    铝电容电极箔阳极化

    公开(公告)号:US4146439A

    公开(公告)日:1979-03-27

    申请号:US905709

    申请日:1978-05-15

    IPC分类号: C25D11/06 H01G9/00

    CPC分类号: H01G9/0032 C25D11/06

    摘要: Current efficiency is increased in the anodization of aluminum foil for electrolytic capacitors by carrying out the anodization below 90.degree. C. in a non-aqueous ethylene glycol-ammonium pentaborate bath containing a small amount of an orthophosphate source, e.g., ammonium dihydrogen phosphate.

    摘要翻译: 在含有少量正磷酸盐源(例如磷酸二氢铵)的非水乙二醇 - 五硼酸铵浴中进行阳极氧化低于90℃,对于电解电容器的铝箔的阳极氧化,电流效率提高。

    AC Etching of aluminum capacitor foil
    4.
    发明授权
    AC Etching of aluminum capacitor foil 失效
    AC电镀铝箔蚀刻

    公开(公告)号:US4427506A

    公开(公告)日:1984-01-24

    申请号:US422931

    申请日:1982-09-24

    CPC分类号: H01G9/055 C25F3/04

    摘要: In the AC etching of aluminum foil in a hydrochloric acid electrolyte containing at least one additive, the presence of 200 to 500 ppm sulfate permits etching thicker foil for higher voltage use than is possible without the sulfate. The additive is chosen from phosphoric, nitric, and tartaric acids or salts. The presence of the relatively small amount of sulfate yields a foil with higher capacitance and generally allows lower temperatures and frequencies to be used.

    摘要翻译: 在含有至少一种添加剂的盐酸电解质中的铝箔的AC蚀刻中,存在200-500ppm的硫酸盐允许在没有硫酸盐的情况下蚀刻较厚的箔以达到更高的电压使用。 添加剂选自磷酸,硝酸和酒石酸或盐。 相对少量的硫酸盐的存在产生具有较高电容的箔,并且通常允许使用较低的温度和频率。

    Treating etched aluminum electrolytic capacitor foil
    6.
    发明授权
    Treating etched aluminum electrolytic capacitor foil 失效
    处理蚀刻铝电解电容器箔

    公开(公告)号:US4204919A

    公开(公告)日:1980-05-27

    申请号:US35145

    申请日:1979-05-02

    IPC分类号: C25D11/16 H01G9/04

    CPC分类号: C25D11/16 H01G9/04

    摘要: Aluminum electrolytic capacitor foil is treated prior to anodization in a two-step process in which a hydrous oxide film is first formed on the foil and the hydrous oxide is then modified. In the first step the foil is immersed in boiling water to form an appropriate thickness of hydrous oxide and in the second step it is immersed in a boiling aqueous solution containing phosphate, silicate, or tartrate ions, or combinations thereof. This treatment results in a decreased power consumption during anodization and produces a film having higher film capacitance.

    摘要翻译: 铝电解电容器箔在阳极氧化之前进行两步法处理,其中首先在箔上形成水合氧化物膜,然后修饰含水氧化物。 在第一步骤中,将箔浸入沸水中以形成适当厚度的氧化亚氮,并且在第二步骤中将其浸入含有磷酸盐,硅酸盐或酒石酸盐离子或其组合的沸腾水溶液中。 这种处理导致阳极氧化期间功率消耗降低并且产生具有更高膜电容的膜。