摘要:
A swivel-type portable flash device includes a C-shaped swivel cover that rotates (swivels) relative to a housing between an open position in which a plug connector is exposed for insertion in a host system, and a closed position in which the plug connector is covered and protected by the swivel cover. The swivel cover is permanently rotatably connected to the housing by way of ring-shaped protrusions that are movably engaged inside corresponding recessed ring-shaped grooves formed in upper/lower walls of the housing, whereby the swivel cover is manually rotatable relative to the housing between the opened and closed positions. The swivel cover also includes locking structures (e.g., locking notches) disposed on the ring-shaped protrusions, and the housing includes second locking structures disposed in the recessed ring-shaped grooves, where the first locking structures operably engage the second locking structures to prevent rotation of the swivel cover when the plug connector is in the closed position.
摘要:
A pen-type computer peripheral device includes an elongated housing containing a PCBA having a plug connector. The PCBA is secured to a positioning member that is actuated by way of a press-push button that is exposed through a slot defined in a wall of the housing. A spring-loaded mechanism includes a spring and a locking mechanism that locks the connector in a retracted position and a deployed position, and the spring biases the connector from the retracted position to the deployed position, or vice versa.
摘要:
A USB device including a housing and a rear cap that is rotatably connected to the housing to facilitate deploying and retracting a plug connector through a front opening of the housing. The plug connector is fixedly connected onto the front end of a sliding rack assembly that is disposed in housing such that the sliding rack assembly is slidable along a longitudinal axis. The sliding rack assembly includes a carrier including a carrier tray for supporting electronic devices and an elongated positioning rod extending from a rear portion of the carrier tray. The positioning rod is operably engaged with an actuator portion such that manual rotation of the rear cap relative to the housing around the longitudinal axis causes the sliding rack assembly to slide inside the housing between retracted and deployed positions.
摘要:
A memory module assembly includes a heat-sink plate attached to one or more of the integrated circuits (e.g., memory devices) of a memory module PCBA by adhesive. The heat-sink plate includes an elongated base structure, a first contact plate extending away from the base structure such that a step-like positioning surface is defined therebetween, and heat-exchange fins extending from the opposite side of the base structure. An optional upper heat-sink plate is secured to a second side of the PCBA by a second adhesive layer, and contacts the lower heat-sink plate to facilitate heat transfer to the heat-exchange fins. The adhesive is either heat-activated or heat-cured. The adhesive is applied to either the memory devices or the heat-sink plates, and then compressed between the heat-sink plates and memory module using a fixture. The fixture is then passed through an oven to activate/cure the adhesive.
摘要:
A pen-type computer peripheral device includes an elongated housing containing a PCBA having a plug connector. The PCBA is secured to a positioning member that is actuated by way of a press-push button that is exposed through a slot defined in a wall of the housing. A spring-loaded mechanism includes a spring and a locking mechanism that locks the connector in a retracted position and a deployed position, and the spring biases the connector from the retracted position to the deployed position, or vice versa.
摘要:
A press-push type computer peripheral “flash drive” device includes an elongated (e.g., metal) tubular casing containing a PCBA having a plug connector. A plastic housing assembly includes front and rear cap portions mounted over the open ends of the tubular casing, and a fixed plastic sleeve portion disposed in the tubular casing. The PCBA is secured to a plastic sliding rack structure that is disposed in the tubular casing and includes an actuating button protruding through a slot formed in a wall of the tubular casing. When the actuating button is manually pushed and slid along the slot, a portion of the sliding rack structure slides against the plastic sleeve portion in deploying and retracting the USB connector out of the device.
摘要:
A Low-power flash-memory device uses a modified Universal-Serial-Bus (USB) 3.0 Protocol to reduce power consumption. The bit clock is slowed to reduce power and the need for pre-emphasis when USB cable lengths are short in applications. Data efficiency is improved by eliminating the 8/10-bit encoder and instead encoding sync and framing bytes as 9-bit symbols. Data bytes are expanded by bit stuffing only when a series of six ones occurs in the data. Header and payload data is transmitted as nearly 8-bits per data byte while framing is 9-bits per symbol, much less than the standard 10 bits per byte. Low-power link layers, physical layers, and scaled-down protocol layers are used. A card reader converter hub allows USB hosts to access low-power USB devices. Only one flash device is accessed, reducing power compared with standard USB broadcasting to multiple devices.
摘要:
A Solid State Drive (SSD) device includes a printed circuit board assembly (PCBA) defining rivet holes, and a support structure including parallel side frame rails defining rivet openings and support platforms for receiving and supporting the PCBA. Compression-mated rivet sets are used to connect the PCBA to the support structure, each rivet set including a female rivet portion and an associated male rivet portion. The PCBA is mounted onto the support structure such that the rivet holes are aligned with the rivet openings of the plurality of rivet openings, and then the rivet sets are mounted and secured using an automatic rivet tool such that each rivet set extends through an associated rivet hole/opening and fixedly engaged such that the PCBA and the support structure are held between end caps of the respective male and female rivet portions.
摘要:
A metal-wrapped flash-memory-drive device has an integrated slim Universal-Serial-Bus (USB) connector that fits into a standard USB socket. The slim USB connector has 4 metal contacts on a circuit board that is encapsulated by a plastic case. Components are mounted onto the circuit board. A metal wrap conforms to the general shape of a plastic sub-assembly of the plastic case and a plastic cover that enclose the circuit board. The metal wrap can be bent around the plastic sub-assembly in a forming process, or can be pre-formed into a metal tube that the plastic sub-assembly is inserted into. Alignment holes in the metal wrap can fit over plastic stubs on the plastic sub-assembly, or friction can hold the metal wrap to the plastic sub-assembly. The plastic cover and case can be bonded together by molding, ultrasonically, with adhesive films, or using snaps to form the plastic sub-assembly.
摘要:
A flash memory device includes one or two panels that are attached solely by a thermal bond adhesive to either a frame or integrated circuits (e.g., flash memory devices) disposed on a PCBA. The frame is disposed around the PCBA and supports peripheral edges of the panels. The thermal bond adhesive is either heat-activated or heat-cured, and is applied to either the memory devices, the frame or the panels, and then compressed between the panels and flash memory devices/frame using a fixture. The fixture is then passed through an oven to activate/cure the adhesive. An optional insulating layer is disposed between the panels and the ICs. An optional conforming coating layer is formed over the ICs for preventing oxidation of integrated circuit leads or soldering area, covering or protecting extreme temperature exposure either cold or hot, and waterproofing for certain military or industrial applications.