摘要:
A PWM controller for controlling a switching voltage regulator comprises a first comparator, a second comparator and a third comparator. The first comparator is configured to detect voltages of a first node and a second node so as to determine whether to stop the PWM controller. The PWM controller is stopped if a first potential is lower than a threshold, and the first potential derives from the voltage of the first node by a level shift of a first voltage difference. The second comparator is configured to detect the voltage of the first node and then to compare the voltage with a power reference voltage so as to determine whether the PWM controller receives necessary power. The third comparator is configured to compare the voltage of the second node with an enable reference voltage so as to determine whether to disable the PWN controller.
摘要:
A low dropout regulator comprises a depletion mode NMOS transistor, a switch and an error amplifier. The source electrode of the depletion type NMOS transistor is coupled to a feedback circuit. The switch, controlled by a control signal, connects a supply voltage to the drain electrode of the depletion mode NMOS transistor. The non-inverting input terminal of the error amplifier is coupled to a reference voltage. The output terminal of the error amplifier is coupled to the gate electrode of the depletion mode NMOS transistor. The inverting input terminal of the error amplifier is coupled to the feedback circuit.
摘要:
An LDO with over-current protection includes a first and a second P-type transistor, a sensing resistor, a comparator, and an error amplifier. The channel aspect ratio of the first P-type transistor is much higher than that of the second P-type transistor. The first P-type transistor generates output voltage source according to input voltage source and current control signal. The sensing resistor is coupled among the input voltage source, the second P-type transistor, and the comparator, providing a sensing voltage. The comparator generates a current limiting signal according to first reference voltage and the sensing voltage. When the current limiting signal enables the error amplifier, the error amplifier adjusts voltage of the current control signal according to second reference voltage and voltage divided from the output voltage source; when the current limiting signal disables the error amplifier, voltage of the current control signal is not adjusted.
摘要:
A pulse width modulation controller comprises a disabling unit, a level sensor and an over current protector. These three devices are all coupled to a multi-function node for accomplishing a disable function, input level sensing, and over-current protection, respectively.
摘要:
The oscillation circuit includes an output current mirror, a P-N complementary current mirror, a P-type current mirror and an N-type current mirror. The P-N complementary current mirror has the same structure as the output current mirror but has current that is only 1/k times the current of the output current mirror, wherein k is greater than 1. The P-type current mirror connects to the P-N complementary current mirror, and has current that is m times the current of the P-N complementary current mirror, where m is greater than 1. The N-type current mirror has one end connected to the P-type current mirror and another end connected to the output current mirror. The N-type current mirror has current that is n times the current of the P-type current mirror, where m × n k ≥ 1 , and n is greater than 1.
摘要:
A low dropout regulator includes an error amplifier, an N-type depletion MOSFET, a first switch, a second switch, a low-pass filter resistor, and a low-pass filter capacitor. By switching on both the first switch and the second switch, a voltage level of an output node at a negative input terminal of the error amplifier may be rapidly raised to be close to and lower than a voltage level of an input node at a gate of the N-type depletion MOSFET. Both the first switch and the second switch are then switched off immediately so that the voltage level of the output node is gradually raised to be equal to the voltage level of the input node through the low-pass filter resistor.
摘要:
The circuit for fixing the peak current of an inductor includes an operating current, a ramp-type boost converter and a comparator. The magnitude of the operating current is proportional to that of the voltage source of the inductor. The ramp-type boost converter is connected to the operating current. One input end of the comparator is connected to a reference voltage, and the other end is connected to the output of the ramp-type boost converter. The output of the comparator is connected to the gate of a power transistor, which controls the turn-on time of the inductor.
摘要:
The circuit for fixing the peak current of an inductor includes an operating current, a ramp-type boost converter and a comparator. The magnitude of the operating current is proportional to that of the voltage source of the inductor. The ramp-type boost converter is connected to the operating current. One input end of the comparator is connected to a reference voltage, and the other end is connected to the output of the ramp-type boost converter. The output of the comparator is connected to the gate of a power transistor, which controls the turn-on time of the inductor.
摘要:
The low voltage circuit for starting up a synchronous step-up DC/DC converter, which connects to a voltage source through an inductor, includes a P-type power transistor, an N-type power transistor and a controller. The P-type power transistor includes a body diode, and one end of the P-type power transistor acts as a power source of an oscillator. The N-type power transistor connects the P-type power transistor in series, and both of the power transistors are not enabled at the same time. The oscillator electrically connects to the controller, which enables the P-type power transistor at initialization time, and enables the N-type power transistor a period after the initialization time.
摘要:
A current sensing module and a power conversion apparatus and an electronic apparatus using the same are provided. The current sensing module is suitable for detecting a first load current flowing through a first load. The current sensing module includes a sampling stage circuit and an output stage circuit. The sampling stage circuit couples across the first load and selectively exchanges coupling nodes between the sampling stage circuit and the first load by a multiplex switching means, so as to sample the first load current flowing along a first direction or a second direction, and thus generate a sampling signal. The output stage circuit is coupled to the sampling stage circuit and switches coupling nodes between the output stage circuit and the output terminal of the sampling stage circuit, so as to generate a current indication signal indicating the magnitude of the first load current according to the sampling signal.