利索-全球专利检索

  1. 登录
  2. 注册

搜索结果

124 条记录 (耗时 0.033 秒)

    Apparatus for transmitting cells, with audio interwork function
    93.
    发明授权
    Apparatus for transmitting cells, with audio interwork function 失效
    用于传输信元的装置，具有音频交互功能

    公开(公告)号：US06347088B1

    公开(公告)日：2002-02-12

    申请号：US09175200

    申请日：1998-10-20

    申请人： Junichi Katou ,  Makoto Watanabe ,  Kenji Shibata ,  Shinichiro Matsuo

    发明人： Junichi Katou ,  Makoto Watanabe ,  Kenji Shibata ,  Shinichiro Matsuo

    IPC分类号： H04L1246

    CPC分类号： H04Q11/0478 ,  H04L2012/5616 ,  H04L2012/563 ,  H04L2012/5663

    摘要： Only one ATM call setting path is set between two ATM-WAN nodes, and ATM communication paths for audio signals of a number corresponding to the number of calls are set. If call setting N-ISDN signals are transmitted from a PBX-A, the IWF of the ATM-WAN nodes on a calling party side stores the call setting N-ISDN signals in ATM cells transparently as they are, and sends the ATM cells to a common ATM call setting path. If call setting channel associated signals are transmitted from a PBX-B, the IWF of the ATM-WAN nodes on a calling party side converts the call setting channel associated signals to call setting N-ISDN signals, stores the converted signals in ATM cells, and sends the ATM cells to a common ATM call setting path.

    摘要翻译： 在两个ATM-WAN节点之间仅设置一个ATM呼叫设置路径，并且设置与呼叫次数对应的号码的音频信号的ATM通信路径。 如果从PBX-A发送呼叫设置N-ISDN信号，主叫方侧的ATM-WAN节点的IWF将ATM信元中的呼叫设置N-ISDN信号透明地存储，并将ATM信元发送到 一个常见的ATM呼叫设置路径。 如果从PBX-B发送呼叫设置信道相关信号，主叫方侧的ATM-WAN节点的IWF将呼叫设置信道相关信号转换为呼叫设置N-ISDN信号，将转换的信号存储在ATM信元中， 并将ATM信元发送到公共ATM呼叫设置路径。

    ATM cell multiplexer
    94.
    发明授权
    ATM cell multiplexer 失效
    ATM信元复用器

    公开(公告)号：US06226264B1

    公开(公告)日：2001-05-01

    申请号：US09038322

    申请日：1998-03-11

    申请人： Kenji Shibata ,  Kazunori Furukawa ,  Yoshihisa Ono

    发明人： Kenji Shibata ,  Kazunori Furukawa ,  Yoshihisa Ono

    IPC分类号： H04L1256

    CPC分类号： H04Q11/0478 ,  H04L2012/5652 ,  H04L2012/5672

    摘要： An ATM cell multiplexer is arranged so that in the up direction from the terminal equipments/ATM cell interfaces to the ATM switchboard the ATM bus scheduler allocates the transmission rights for each CLAD unit in accordance with a preset schedule table and predetermined service categories or traffic control for the transmission of cells, and in the down direction from the ATM switchboard to the terminal equipments/ATM cell interfaces the cells are broadcast to all of the CLAD units which decide for the reception of the cells as to whether or not the cells are addressed to themselves.

    摘要翻译： ATM信元多路复用器被配置为使得在从终端设备/ ATM信元接口到ATM交换机的上行方向上，ATM总线调度器根据预设的调度表和预定的业务类别或业务控制分配每个CLAD单元的传输权限 对于小区的传输，并且在从ATM交换机到终端设备/ ATM信元接口的向下的方向上，这些小区被广播到所有CLAD单元，这些单元决定单元是否被寻址 给自己

    Steering shaft
    95.
    发明授权
    Steering shaft 有权
    转向轴

    公开(公告)号：US06223619B1

    公开(公告)日：2001-05-01

    申请号：US09437609

    申请日：1999-11-10

    申请人： Kenji Shibata ,  Mitsuo Hoshino ,  Katuhiko Fujita ,  Hitoshi Matsumoto

    发明人： Kenji Shibata ,  Mitsuo Hoshino ,  Katuhiko Fujita ,  Hitoshi Matsumoto

    IPC分类号： B62D116

    CPC分类号： B62D1/192 ,  B29C45/14491 ,  F16D3/06

    摘要： A steering shaft includes: an outer shaft having an inner splined portion; an inner shaft having a shaft portion and an outer splined portion which are arranged continuously along an axial direction; a retaining portion formed on at least one of the outer splined portion and the shaft portion; a sliding coupling section formed by a coupling portion of the outer shaft and a coupling portion of the inner shaft so as to allow the outer shaft and the inner shaft to be telescopically slidable in the axial direction relative to each other by means of splines; and a sliding resin member which is filled in a space formed in the sliding coupling section between an opening portion of the outer shaft and the retaining portion of the inner shaft.

    摘要翻译： 转向轴包括：具有内花键部分的外轴; 具有沿轴向连续配置的轴部和外花键部的内轴; 保持部，形成在所述外花键部和所述轴部中的至少一个上; 滑动联接部，其由所述外轴的联接部和所述内轴的联接部形成，以使得所述外轴和所述内轴能够通过花键相对于彼此在轴向方向上可伸缩地滑动; 以及滑动树脂构件，其被填充在形成在所述滑动联接部分中的空间中，所述空间在所述外轴的开口部分和所述内轴的保持部分之间。

    CMOS semiconductor device
    98.
    发明授权
    CMOS semiconductor device 失效
    CMOS半导体器件

    公开(公告)号：US4740827A

    公开(公告)日：1988-04-26

    申请号：US913383

    申请日：1986-09-30

    申请人： Youichiro Niitsu ,  Shinji Taguchi ,  Kenji Shibata ,  Kouichi Kanzaki

    发明人： Youichiro Niitsu ,  Shinji Taguchi ,  Kenji Shibata ,  Kouichi Kanzaki

    IPC分类号： H01L21/762 ,  H01L21/8238 ,  H01L27/092 ,  H01L29/78 ,  H01L27/02 ,  H01L27/12 ,  H01L29/06

    CPC分类号： H01L21/823878 ,  H01L21/7621 ,  H01L27/0921

    摘要： In the CMOS semiconductor device having an epitaxial layer, a trench with an appropriate depth is formed in the vicinity of a boundary between a range in which a MOS transistor is formed and a well range in which another MOS transistor is formed; the inner wall surface of the trench is covered with a thermal oxide film; and the trench is buried with a semiconductor substance, so that two CMOS transistors can be electrically isolated by the trench to increase the latch-up holding voltage beyond a supply voltage (e.g. 5 v). Therefore, the latch-up proof resistance can be increased to protect the device from noise which otherwise would break the device. Further, the trench depth is shallower than the low impurity atom concentration layer (epitaxial layer) or 3 .mu.m but deeper than a value obtained by subtracting 2 .mu.m from the above thickness or 3 .mu.m.

    摘要翻译： 在具有外延层的CMOS半导体器件中，在形成MOS晶体管的范围与形成另一MOS晶体管的阱范围之间的边界附近形成适当深度的沟槽; 沟槽的内壁表面被热氧化膜覆盖; 并且沟槽被半导体物质掩埋，使得两个CMOS晶体管可以通过沟槽电隔离以增加闩锁保持电压超过电源电压（例如5V）。 因此，可以提高防闩锁电阻以保护装置免受噪声，否则会破坏装置。 此外，沟槽深度比低杂质原子浓度层（外延层）浅3μm，但比通过从上述厚度或3μm减去2μm获得的值更深。

    Process for production of high-manganese iron alloy by smelting reduction
    99.
    发明授权
    Process for production of high-manganese iron alloy by smelting reduction 失效
    通过冶炼还原生产高锰铁合金的工艺

    公开(公告)号：US4662937A

    公开(公告)日：1987-05-05

    申请号：US737406

    申请日：1985-05-24

    申请人： Hiroyuki Katayama ,  Hidetake Ishikawa ,  Masatoshi Kuwabara ,  Hiroyuki Kajioka ,  Masaki Fujita ,  Kenji Shibata ,  Yoshiaki Tamura ,  Takashi Shimanuki

    发明人： Hiroyuki Katayama ,  Hidetake Ishikawa ,  Masatoshi Kuwabara ,  Hiroyuki Kajioka ,  Masaki Fujita ,  Kenji Shibata ,  Yoshiaki Tamura ,  Takashi Shimanuki

    IPC分类号： C21C5/35 ,  C22C33/00 ,  C22B47/00

    CPC分类号： C22C33/003 ,  C21C5/35

    摘要： There is provided a process for producing a high-manganese iron alloy from a manganese ore and/or a pre-reduced product thereof in a top and bottom blown converter type reaction vessel holding molten iron or a molten manganese iron alloy, together with a molten slag, said molten iron or alloy and said molten slag being the products of a separate smelting furnace, gas being blown into said vessel through a bottom blowing nozzle, said process comprising charging said vessel with a supply of raw materials including at least one source of manganese and iron selected from a manganese ore containing manganese oxide and iron oxide and a pre-reduced product thereof, a solid carbonaceous substance and a slag forming agent, while simultaneously blowing gas selected from oxygen and a gas containing oxygen into said vessel through a top blowing lance to burn said carbonaceous substance so as to heat, melt and reduce said raw materials to form a melt containing manganese oxide and iron oxide; supplying an additional carbonaceous substance into said melt to reduce said manganese oxide and said iron oxide to form a molten high-manganese iron alloy and a molten slag, discontinuing said blowing of gas through said top blowing lance, and removing said molten high-manganese iron alloy and said molten slag from said vessel, said molten alloy being used for casting.

    摘要翻译： 本发明提供一种在含有铁水或熔融锰铁合金的顶部和底部转化型反应容器中从锰矿石和/或其预还原产物生产高锰铁合金的方法，以及熔融 熔渣，所述熔融铁或合金，所述熔融炉渣是单独熔炼炉的产物，气体通过底吹喷嘴吹入所述容器中，所述方法包括向原料供应原料，该原料包括至少一种 选自含有锰氧化物和氧化铁的锰矿及其预还原产物，固体碳质物质和成渣剂的锰和铁，同时通过顶部将从氧气和含氧气体中选出的气体吹入所述容器中 吹枪吹烧所述碳质物质，以加热，熔化和还原所述原料以形成含有氧化锰和氧化铁的熔体; 向所述熔体中提供另外的碳质物质以减少所述氧化锰和所述氧化铁以形成熔融的高锰铁合金和熔渣，停止通过所述顶吹喷枪吹入气体，并且除去所述熔融的高锰铁 合金和来自所述容器的所述熔渣，所述熔融合金用于铸造。

    Electrodialysis desalination process and system for seawater
    100.
    发明授权
    Electrodialysis desalination process and system for seawater 失效
    电渗析脱盐工艺及海水系统

    公开(公告)号：US4539091A

    公开(公告)日：1985-09-03

    申请号：US537550

    申请日：1983-10-03

    申请人： Hiroshi Kaneda ,  Kenji Shibata ,  Mitugu Nomura ,  Fumihiko Sano

    发明人： Hiroshi Kaneda ,  Kenji Shibata ,  Mitugu Nomura ,  Fumihiko Sano

    IPC分类号： C02F1/46 ,  C02F1/469 ,  B01D13/02

    CPC分类号： C02F1/4693 ,  B01D61/44 ,  C02F1/4604 ,  B01D2311/06 ,  B01D2313/36 ,  B01D2313/38 ,  C02F2103/08 ,  C02F2201/46115 ,  C02F2201/4612 ,  C02F2201/46145 ,  C02F2209/02 ,  Y10S203/01 ,  Y10S203/11

    摘要： An electrodialysis desalination process for seawater comprising the steps of collecting seawater and heating same by solar heat; subjecting seawater thus heated to electrodialysis; and separating same into two portions of a diluted solution and a concentrated brine, is provided, as well as the same system comprising a preheater utilizing solar heat for preheating seawater, an electrodialyser for separating seawater thus preheated by said preheater into said two portions, and means for supplying seawater to the preheater and then from the preheater to the electrodialyser. Various modifications of the above process and system are disclosed. According to the present inventions, electric power consumption in the electrodialysis is saved and solar heat is utilized effectively.

    摘要翻译： 一种用于海水的电渗析脱盐方法，包括通过太阳热收集海水并加热其的步骤; 使经加热的海水进行电渗析; 并将其分离成两部分稀释溶液和浓缩盐水，以及包括利用太阳能热预热海水的预热器的相同系统，用于将由所述预热器预热的海水分离成所述两部分的电渗析器，以及 用于将海水供应到预热器，然后从预热器供应到电渗析器的装置。 公开了上述过程和系统的各种修改。 根据本发明，可以节省电渗析中的电力消耗，有效利用太阳能热。