摘要:
An extended Universal-Serial-Bus (USB) connector plug and socket each have a pin substrate with one surface that supports the four metal contact pins for the standard USB interface. An extension of the pin substrate carries another 8 extension metal contact pins that mate when both the connector plug and socket are extended. The extension can be an increased length of the plug's and socket's pin substrate or a reverse side of the substrate. Standard USB connectors do not make contact with the extension metal contacts that are recessed, retracted by a mechanical switch, or on the extension of the socket's pin substrate that a standard USB connector cannot reach. Standard USB sockets do not make contact with the extension metal contacts because the extended connector's extension contacts are recessed, or on the extension of the connector pin substrate that does not fit inside a standard USB socket.
摘要:
A portable USB device is described herein. According to one embodiment, a portable USB device includes a core unit having a USB plug connector coupled to one or more multi-level cell (MLC) flash memory devices and an MLC flash controller disposed therein. The device further includes a housing for enclosing the core unit. The device further includes a swivel cap having a top surface and a bottom surface by bending a flat panel into a U-shape block having an opening end, a close end, and two side-openings, where the top and bottom surfaces of the swivel cap include a rivet opening align with each other. The housing having the core unit therein is sandwiched by the swivel cap using a set of rivets through the rivet openings of the housings and the swivel cap. The core unit can be rotated with respect to the rivet set in and out of the swivel cap.
摘要:
A USB plug receptacle includes a connector substrate having a tongue portion having a first set of electrical contact pins disposed on a top surface of the tongue portion, a second set of a plurality of electrical pins disposed on a bottom surface of the tongue portion, a third set of electrical contact pins disposed on an opposite end of the tongue portion. The USB plug receptacle further includes a metal case made of a sheet of electrically conductive metal plate by blanking the sheet into a generally tubular shape to receive and enclose the connector substrate. When the connector substrate is inserted into the metal case, the third set of electrical contact pins are exposed outside of the metal case and the third set of electrical contact pins can be mounted on first and second sets of electrical contact pads of a printed circuit board assembly.
摘要:
An extended Universal-Serial-Bus (USB) connector plug and socket each have a pin substrate with one surface that supports the four metal contact pins for the standard USB interface. An extension of the pin substrate carries another 8 extension metal contact pins that mate when both the connector plug and socket are extended. The extension can be an increased length of the plug's and socket's pin substrate or a reverse side of the substrate. Standard USB connectors do not make contact with the extension metal contacts that are recessed, retracted by a mechanical switch, or on the extension of the socket's pin substrate that a standard USB connector cannot reach. Standard USB sockets do not make contact with the extension metal contacts because the extended connector's extension contacts are recessed, or on the extension of the connector pin substrate that does not fit inside a standard USB socket.
摘要:
A portable USB device with an improved configuration is described herein. According to one embodiment, a portable USB device includes a core unit having a USB plug connector coupled to one or more flash memory devices and a flash controller disposed therein, where the flash controller is capable of exchanging data with a host via the USB plug connector using a bulk-only-transfer protocol. The portable USB device further includes a housing for enclosing the core unit, including a front end opening to allow the USB plug connector to be deployed. The portable USB device further includes a core unit carrier for carrying the core unit for deploying and retracting the core unit, including a slide button to allow a finger of a user to slide the USB plug connector of the core unit in and out of the housing via the front end opening of the housing.
摘要:
A case-grounded flash-memory drive has a printed-circuit board assembly (PCBA) with flash-memory chips and a controller chip. The PCBA is encased inside an upper case and a lower case, with a Serial AT-Attachment (SATA) connector that fits through and opening between the cases. The cases can be assembled with the PCBA by a snap-together, ultrasonic-press, screw-fastener, or thermal-bond adhesive method. Dual-axis case-grounding pins draw any electro-static-discharges (ESD) current off the upper case along a primary axis and onto a PCBA ground through a secondary axis washer that is screwed into the PCBA. The primary axis body of the dual-axis case-grounding pins fits around a PCBA notch while the secondary axis passes through a metalized alignment hole for grounding. When the SATA connector is inserted into a host, the host ground sinks ESD currents collected by the dual-axis case-grounding pins.
摘要:
A Universal-Serial-Bus (USB) device has a USB plug with reduced wobble. A USB metal wrap around the perimeter of the USB plug is attached to a housing by overmolding. A plug supporter is inserted into the front of the USB metal wrap, and has locking tabs that snap over the inside wall of the housing. Side tabs on the plug supporter fit into side slots on the USB metal wrap to secure the plug supporter inside the USB metal wrap. A circuit board with a USB flash controller has USB metal contacts on an extension end that is inserted through the housing and into the USB metal wrap. The extension end fits underneath top tabs on the plug supporter, preventing the extension end with the USB metal contacts from upward wobble when the USB plug is inserted into a USB socket.
摘要:
A Universal-Serial-Bus (USB) device has a USB plug that is centered over a center-line of a circuit board. The circuit board with flash memory and a USB flash controller has metal pads that a USB connector is soldered to. The USB connector has a rear step that is about half the height of the USB connector plug. Contacts on the rear step are soldered to the metal pads on the circuit board so that the USB connector is centered around the edge of the circuit board. The overall height of the flash device can be reduced since the bulky USB connector is not attached off-center to the circuit board, but is attached at the half-height rear step. Both the USB connector and the circuit board share the same center line, allowing a printed-circuit board assembly (PCBA) to be symmetric around the center line.
摘要:
An open-frame flash-memory drive has a printed-circuit board assembly (PCBA) with flash-memory chips, a controller chip, and a Serial AT-Attachment (SATA) connector soldered to it. The PCBA is only partially encased by left and right frames or by a U-shaped bracket frame. The frames have PCBA supports and guide posts that fit near edges of the PCBA. The frames do not cover the top and bottom of the PCBA, allowing chips on the PCBA to be ventilated by unblocked air flow. Screws that attach the PCBA to the frame have metal collars that ground the frame to the PCBA's ground plane. The screws form a current path to draw any electro-static-discharge (ESD) current off the frame and onto a PCBA ground. When the SATA connector is inserted into a host, the host ground sinks ESD currents collected by the open frame.
摘要:
A method for fabricating MicroSD devices includes forming a PCB panel having multiple PCBs arranged in parallel rows, with each PCB connected to its neighboring PCBs in each row by relatively narrow connecting bridge pieces, and separated from PCBs of adjacent rows by elongated stamped out blank slots. Passive components are attached by conventional surface mount technology (SMT) techniques. IC chips, including a MicroSD controller chip and a flash memory chip, are attached to the PCB by wire bonding or other chip-on-board (COB) technique. A molded housing is then formed over the IC chips and passive components using a mold that prevents formation of plastic on the upper surface of each PCB. The connecting bridge pieces are then cut using a used to connect each PCB to a PCB panel are then cut using a rotary saw. A front edge chamfer process is then performed.