摘要:
A process control method includes discretizing a physical process by particle-based domain decomposition into a plurality of partial volumes where one particle replaces a multiplicity of objects interacting within the particular partial volume and defines a first process parameter of the process. The method further includes calculating a second process parameter for the inner particles of the process area by LME approximation and calculating the second process parameter for the outer particles by MLS approximation. The method further includes calculating an interaction variable for the inner particles of the process area by LME approximation and the interaction variables for the outer particles by MLS approximation. The method further includes calculating at least one control variable on the basis of the interaction variables calculated for the inner and outer particles. The method further includes setting a target process parameter for the physical process by the calculated control variable.
摘要:
In a method for diagnosing an internal combustion engine having first and second fuel injectors, if a misfire is detected, the following steps are performed in sequence: a first fuel quantity of the fuel is introduced only by the first fuel injector; a check is performed to determine whether a misfire results from the introduction of a first fuel quantity in the first step; a second fuel quantity of the fuel is introduced only by the second fuel injector; a check is performed to determine whether a misfire results from the introduction of the second fuel quantity in the third step; and an engine error is diagnosed if a misfire was detected in the second or in the fourth step.
摘要:
A method and a device for the diagnosis of at least one gas exchange valve of at least one cylinder of an internal combustion engine that is on the one hand reliable and on the other hand does without additional sensor equipment are described. In a first operating state of the internal combustion engine, at least one gas exchange valve of the at least one cylinder is activated. In a second operating state of the internal combustion engine, all the gas exchange valves of the at least one cylinder are deactivated and therewith closed in stationary fashion. Sound waves produced by the internal combustion engine are acquired. It is checked whether a significant change occurs in a quantity characterizing the acquired sound waves upon a transition from the first operating state to the second operating state. In this case, an erroneous opening of the at least one gas exchange valve is recognized.
摘要:
A method is provided for operating an internal combustion engine having a plurality of cylinder banks, of which at least one first cylinder bank is able to be deactivated. At least one cylinder of the first cylinder bank is intermittently activated again during the deactivation of the first cylinder bank.
摘要:
A method for operating an internal combustion engine having a plurality of cylinder banks provides a cylinder cut-off using at least a reduced ignition angle retardation shift. In this context, at least one first cylinder bank is configured such that it is at least partially able to be cut off. Immediately before a cut off or immediately after a reactivation of at least one cylinder of the at least one first cylinder bank, a first output variable is set for the at least one first cylinder bank and a second output variable is set for at least one second cylinder bank. The first output variable and the second output variable are set differently from each other in such a way that an average of the first and second output variables is equivalent to a predetermined output variable of the internal combustion engine.
摘要:
A method and an arrangement for controlling the drive unit of a vehicle make possible the jolt-free enablement of a rapid actuating path (5) for the conversion of a desired value for an output quantity of the drive unit. The desired value for the output quantity of the drive unit is pregiven. Depending upon the operating state of the drive unit, an actual value for the output quantity is caused to track the desired value via a slow actuating path (1) or the rapid actuating path (5). With a transition from the slow actuating path (1) to the rapid actuating path (5), the desired value, starting from the wanted value, is first set equal to the actual value and thereafter is limited in its change and is again brought back to the wanted value.
摘要:
A method for operating an internal combustion engine having a plurality of cylinder banks provides a cylinder cut-off using at least a reduced ignition angle retardation shift. In this context, at least one first cylinder bank is configured such that it is at least partially able to be cut off. Immediately before a cut off or immediately after a reactivation of at least one cylinder of the at least one first cylinder bank, a first output variable is set for the at least one first cylinder bank and a second output variable is set for at least one second cylinder bank. The first output variable and the second output variable are set differently from each other in such a way that an average of the first and second output variables is equivalent to a predetermined output variable of the internal combustion engine.
摘要:
A method and an arrangement control the output quantity (NMOTACT) of a drive unit (1) of a vehicle. The method and arrangement make possible a time-optimal control strategy especially during a shift operation of the vehicle. The output quantity (NMOTACT) is adjusted with the aid of an adjusting quantity (MDES) and tracks an input value (NMOTDES). In at least one pregiven operating state of the vehicle, the actuating quantity (NMOTDES) is brought to a pregiven limit value (MO, MU) when a pregiven control deviation (dnv) of the output quantity (NMOTACT) is exceeded.
摘要:
A method for milling long fibre reinforced composite plastics having at least one unidirectional top layer using a rotating milling tool, wherein work piece and tool are moved in an advancing movement parallel to the work piece cutting face relative to each other, and wherein there is an edge fibre separation angle on the work piece of 0°≦θedge≦90°, and the blade of the tool mills the component edge in synchronization.
摘要:
A configuration device for the graphical creation of at least one test sequence for controlling a test device having at least one electronic computer. The test device is controllable according to the created test sequence. The configuration device has at least one display device, graphical library functional elements being displayed with the display device in a library field. The test sequence can be created by placing at least one instance of a library functional element in a configuration field. The instance of a library functional element is placed in the configuration field. The graphical library functional element can be provided with a function placeholder, whereby the function placeholder in the instance of the library functional element can be provided with an instance functionality, whereby the reference of the instance of the library functional element to the library functional element is retained.